XT22: Difference between revisions

From airraidsirens.net, the Internet's premiere site for siren information and discussion
Jump to navigation Jump to search
No edit summary
m (ArxCyberwolf moved page Federal Signal XT22 to XT22)
 
(9 intermediate revisions by 2 users not shown)
Line 1: Line 1:
{{Infobox siren
{{Infobox siren|title=Federal Signal 2T22
|title= 2T22 and 3T22
-------------
|image= [[File:3t22 official.jpg|thumbnail|3T22]]
Federal Signal 3T22|image=3t22 official.jpg|caption=Federal Signal 3T22|company=Federal Sign & Signal Company
[[File:2T22.png|thumb|A 2T22. Note the lack of solenoid boxes.]]
<div>[[Federal Signal Corporation]]</div>|produced=1955-1992|type=Omnidirectional Electromechanical|output=113 dB @ 100 feet|hz=50/60|hp=7.5-10 hp|voltage=208-240/480|current=1 or 3 ph|preceded=[[Federal Electric Fedelcode]]
|company= [[Federal Signal Corporation]]
[[Federal Electric Type Mach. B]]
|type =[[Electromechanical]]
<div>[[Federal Signal Model 5]]</div>|succeeded=[[Federal Signal Model ECLIPSE]]|manual=http://civildefensemuseum.com/sirens/manuals/255A152H-2T22-3T22.pdf}}The '''XT22''' ('''2''' ''or'' '''3''' '''T'''one, '''22''' horns/ports) is a pair of dual rotor omnidirectional sirens that were produced by Federal Signal over a span of nearly 40 years. The XT22 line has two variants, the '''2T22''' and '''3T22'''. These are some of the most well-known and iconic sirens with a distinctive sound, and are still commonly found today.  
|output= 113
|neigh= 7.5 - 10
|manual= http://www.civildefensemuseum.com/sirens/manuals/255A152H-2T22-3T22.pdf
}}
== General ==
The 2/3T22 was an omnidirectional siren produced by [[Federal Signal Corporation]]. The design features a single motor in the middle with a twelve-port rotor/stator set on top and a 10-port set on bottom. Both rotors measured 14 inches in diameter, and are identical to rotors used on the model 3 and 2001. The 3T22 model featured solenoids attached to the top and bottom intakes to produce a third signal. The 2T22 lacked the additional signal option.


Both models were available in single and three phase versions. Three phase models used either a GE (early) or Marathon 10 horsepower motor. The only motor used on the single phase model was the Northwestern Electric 7 1/2 horsepower repulsion-induction motor.
''Note that XT22 is not the name of the sirens, rather a way of describing both models at once for brevity. It is also a commonly used name when one is unsure whether a unit is a 2T or 3T. The XT22 name was created by enthusiasts and not used by Federal themselves.''


A fully assembled siren weighs close to 700 pounds, including the pole mount bracket.
== History and design ==
 
=== Overview ===
The XT22 is a simple vertical dual rotor siren, with 15-inch rotors/stators on each side of a dual shaft AC electric motor, with the top rotor being 12-port and the bottom rotor being 10-port, resulting in the XT22 being a 10/12-port dual tone siren. Each rotor has a long intake tube with mesh screens to prevent debris from getting inside, with the upper intake including a rain shield to keep moisture and debris from getting into the top rotor. Each port on the stator has a rounded horn of its own, similar to the [[Federal Signal STH-10|STH-10]] and [[Federal Signal STL-10|STL-10]], with 12 on top and 10 on the bottom. Due to being made of thin sheet metal, these horns are prone to warping and damage, and it is not uncommon to find XT22s with damaged or even missing horns.
 
Three-phase units (designated 2T22A and 3T22A on Federal Signal-era units) are powered by a bare dual sided 7.5 hp or 10 hp AC motor, which was originally manufactured by GE for early FS&S models, and by Marathon for later models. Units with GE motors are slightly shorter than units with Marathon motors. The XT22 also was available in single-phase (designated 2T22B and 3T22B on Federal Signal era units), using a 7.5 hp Northwestern Electric brushed motor. These are often lower pitched due to peaking at a lower RPM, but are capable of reaching a higher pitch than three phase units if there is low enough air resistance due to being non-synchronous (typically due to a blocked intake). These motors are physically taller than the other motors, making the XT22B easy to differentiate from a XT22A.
 
The XT22 is able to reach 113 dB at 100 ft, which is respectable for a dual tone omnidirectional siren and outperforming most of Federal's omnidirectional offerings at the time of its production.
 
While the XT22 is a simple siren that requires little maintenance, it is not without its issues. The cover on the top intake proved insufficient for keeping debris out, which often lead to these sirens having a blocked top intake, rendering the 12-port side near useless. This is especially the case for the 3T22, because the damper makes it even easier for the intakes to clog. In addition, the solenoids which operate the dampers on 3T22 units can freeze up and stop working if left unused for an extended period of time, or the return spring can fail and leave the damper stuck shut.
 
Because of the increasing age of the design, as well as the lack of a need for dual tone sirens after the Cold War ended, the XT22 was discontinued in 1992. However, a healthy, normally functioning 2T22 or 3T22 is a great siren, which is why they are still a common find across the United States, being used as fire or severe weather sirens. While some have since been replaced by newer DC-operated sirens such as the [[Federal Signal Model ECLIPSE|ECLIPSE-8]] or ASC's [[ASC Tempest|Tempest-121,]] or rotational sirens, many cities have chosen to keep these aging beasts as with proper maintenance, these continue to be great sirens.
 
== Models ==
 
=== 3T22 ===
The 3T22 was first produced in 1955, at the dawn of the Cold War. Federal lacked a siren with three-signal capabilities that also met Federal Civil Defense requirements for a dual tone siren. Federal's existing dual tone sirens used a single rotor, which were not capable of creating a hi-lo signal. Federal decided to take inspiration from the dual rotor sirens that were used by Britain during World War 2, but with enhanced performance through the use of horns and a more powerful 60 hz motor. From the beginning, the 3T22 was designed as a three-signal siren, which could be used for civil defense and domestic use, particularly for fire departments and industrial zones.
 
The 3T22 is equipped with two solenoid-driven dampers, with one on each rotor's intake. When the solenoids are energized, the dampers slam shut, restricting airflow to the chopper and greatly reducing the noise. When the solenoid is de-energized, a return spring forces the damper back into the open position, allowing air to flow again. When the two dampers alternate between open and closed while the siren is running, this creates a "hi-lo" signal. The dampers are also capable of operating in unison, creating a "pulse" signal. When the siren shuts off, both dampers automatically de-energize and open. Unfortunately, if the dampers are not maintained properly, the return spring can fail, causing the damper to be sucked shut when the siren activates, which prevents the rotor from reaching its full volume and leading to one rotor massively overpowering the other. The solenoid mechanisms themselves can also become stuck if they aren't maintained or used regularly. Because of this, it can be very difficult to find a 3T22 that has both dampers working, as they are not used frequently and most have opted to cease using a third signal.
 
=== 2T22 ===
Later on at an unknown date, the two-signal 2T22 would be released as an alternative to the 3T22. The 2T22 lacks the dampers and solenoid mechanisms that the 3T22 has, which makes the siren lighter and cheaper to produce, but also renders it incapable of performing a third signal. This can be a benefit, however, as the lack of dampers means the siren is less prone to intake clogs and requires far less maintenance. The 2T22 was fairly popular, though many places opted for the 3T22, even though most did not utilize the three signal capabilities. The 2T22 is entirely identical to the 3T22 with the exception of the dampers, and retains the extended intakes of the 3T22, likely as a cost saving measure.  The 2T22 would be produced alongside the 3T22 until their discontinuation in 1992, with Federal opting to continue producing the STH-10 instead.
[[Category:Federal Signal Corporation]][[Category:Omnidirectional Sirens]][[Category:Dual Toned Sirens]][[Category:Sirens]][[Category:Electromechanical Sirens]]
[[Category:Federal Signal Corporation]][[Category:Omnidirectional Sirens]][[Category:Dual Toned Sirens]][[Category:Sirens]][[Category:Electromechanical Sirens]]
[[Category:Three-Signal Sirens]]
__INDEX__

Latest revision as of 21:03, 24 October 2024

Federal Signal 2T22

Federal Signal 3T22


Federal Signal 3T22

Company Federal Sign & Signal Company
Produced 1955-1992
Type Omnidirectional Electromechanical
Sound output 113 dB @ 100 feet
Frequency 50/60 Hz
Horsepower 7.5-10 hp
Voltage 208-240/480 V 1 or 3 ph
Preceded by Federal Electric Fedelcode

Federal Electric Type Mach. B

Succeeded by Federal Signal Model ECLIPSE
Documentation Manual

The XT22 (2 or 3 Tone, 22 horns/ports) is a pair of dual rotor omnidirectional sirens that were produced by Federal Signal over a span of nearly 40 years. The XT22 line has two variants, the 2T22 and 3T22. These are some of the most well-known and iconic sirens with a distinctive sound, and are still commonly found today.

Note that XT22 is not the name of the sirens, rather a way of describing both models at once for brevity. It is also a commonly used name when one is unsure whether a unit is a 2T or 3T. The XT22 name was created by enthusiasts and not used by Federal themselves.

History and design

Overview

The XT22 is a simple vertical dual rotor siren, with 15-inch rotors/stators on each side of a dual shaft AC electric motor, with the top rotor being 12-port and the bottom rotor being 10-port, resulting in the XT22 being a 10/12-port dual tone siren. Each rotor has a long intake tube with mesh screens to prevent debris from getting inside, with the upper intake including a rain shield to keep moisture and debris from getting into the top rotor. Each port on the stator has a rounded horn of its own, similar to the STH-10 and STL-10, with 12 on top and 10 on the bottom. Due to being made of thin sheet metal, these horns are prone to warping and damage, and it is not uncommon to find XT22s with damaged or even missing horns.

Three-phase units (designated 2T22A and 3T22A on Federal Signal-era units) are powered by a bare dual sided 7.5 hp or 10 hp AC motor, which was originally manufactured by GE for early FS&S models, and by Marathon for later models. Units with GE motors are slightly shorter than units with Marathon motors. The XT22 also was available in single-phase (designated 2T22B and 3T22B on Federal Signal era units), using a 7.5 hp Northwestern Electric brushed motor. These are often lower pitched due to peaking at a lower RPM, but are capable of reaching a higher pitch than three phase units if there is low enough air resistance due to being non-synchronous (typically due to a blocked intake). These motors are physically taller than the other motors, making the XT22B easy to differentiate from a XT22A.

The XT22 is able to reach 113 dB at 100 ft, which is respectable for a dual tone omnidirectional siren and outperforming most of Federal's omnidirectional offerings at the time of its production.

While the XT22 is a simple siren that requires little maintenance, it is not without its issues. The cover on the top intake proved insufficient for keeping debris out, which often lead to these sirens having a blocked top intake, rendering the 12-port side near useless. This is especially the case for the 3T22, because the damper makes it even easier for the intakes to clog. In addition, the solenoids which operate the dampers on 3T22 units can freeze up and stop working if left unused for an extended period of time, or the return spring can fail and leave the damper stuck shut.

Because of the increasing age of the design, as well as the lack of a need for dual tone sirens after the Cold War ended, the XT22 was discontinued in 1992. However, a healthy, normally functioning 2T22 or 3T22 is a great siren, which is why they are still a common find across the United States, being used as fire or severe weather sirens. While some have since been replaced by newer DC-operated sirens such as the ECLIPSE-8 or ASC's Tempest-121, or rotational sirens, many cities have chosen to keep these aging beasts as with proper maintenance, these continue to be great sirens.

Models

3T22

The 3T22 was first produced in 1955, at the dawn of the Cold War. Federal lacked a siren with three-signal capabilities that also met Federal Civil Defense requirements for a dual tone siren. Federal's existing dual tone sirens used a single rotor, which were not capable of creating a hi-lo signal. Federal decided to take inspiration from the dual rotor sirens that were used by Britain during World War 2, but with enhanced performance through the use of horns and a more powerful 60 hz motor. From the beginning, the 3T22 was designed as a three-signal siren, which could be used for civil defense and domestic use, particularly for fire departments and industrial zones.

The 3T22 is equipped with two solenoid-driven dampers, with one on each rotor's intake. When the solenoids are energized, the dampers slam shut, restricting airflow to the chopper and greatly reducing the noise. When the solenoid is de-energized, a return spring forces the damper back into the open position, allowing air to flow again. When the two dampers alternate between open and closed while the siren is running, this creates a "hi-lo" signal. The dampers are also capable of operating in unison, creating a "pulse" signal. When the siren shuts off, both dampers automatically de-energize and open. Unfortunately, if the dampers are not maintained properly, the return spring can fail, causing the damper to be sucked shut when the siren activates, which prevents the rotor from reaching its full volume and leading to one rotor massively overpowering the other. The solenoid mechanisms themselves can also become stuck if they aren't maintained or used regularly. Because of this, it can be very difficult to find a 3T22 that has both dampers working, as they are not used frequently and most have opted to cease using a third signal.

2T22

Later on at an unknown date, the two-signal 2T22 would be released as an alternative to the 3T22. The 2T22 lacks the dampers and solenoid mechanisms that the 3T22 has, which makes the siren lighter and cheaper to produce, but also renders it incapable of performing a third signal. This can be a benefit, however, as the lack of dampers means the siren is less prone to intake clogs and requires far less maintenance. The 2T22 was fairly popular, though many places opted for the 3T22, even though most did not utilize the three signal capabilities. The 2T22 is entirely identical to the 3T22 with the exception of the dampers, and retains the extended intakes of the 3T22, likely as a cost saving measure. The 2T22 would be produced alongside the 3T22 until their discontinuation in 1992, with Federal opting to continue producing the STH-10 instead.